KeeYees 5M GT2 Timing Belt 6mm Width + 4pcs 20 Teeth 5mm Bore Belt Pulley Wheel + 4pcs Idler + 4pcs Tensioner Spring Torsion + 2pcs Gear Clamp Mount Block with Allen Wrench for 3D Printer RepRap
SKU: AMC5360666812- Timing belt: The timing belt is made of premium rubber, durable and flexible. It’s designed specifically for linear motion, high positioning accuracy. Round tooth profile guarantees that the belt tooth fits smoothly.
- Pulley: It’s used together with timing belt, very convenient to use. 20 Teeth contact with the belt, that minimizes the chance of the belt slipping.
- Locking Spring: With the springs, you can add the right tension you need and make your prints much more precise.
KeeYees Pro Micro ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino IDE Leonardo Bootloader
SKU: AMC004536298- ATMega32U4 running at 5V/16MHz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V.
- Supported by Arduino IDE V1.0.1; 4 x 10-bit ADC pins, 12 x Digital I/Os; Rx and Tx Hardware Serial Connections.
- Just connect to the On-Board micro-USB connector for programming. (If this module cannot be recognized by your computer, please refer to this link to install the driver https://www.arduino.cc/en/Guide/DriverInstallation)
KeeYees 5M GT2 Timing Belt 6mm Width + 4pcs 20 Teeth 5mm Bore Belt Pulley Wheel + 4pcs Idler + 4pcs Tensioner Spring Torsion + 2pcs Gear Clamp Mount Block with Allen Wrench for 3D Printer RepRap
- Timing belt: The timing belt is made of premium rubber, durable and flexible. It’s designed specifically for linear motion, high positioning accuracy. Round tooth profile guarantees that the belt tooth fits smoothly.
- Pulley: It’s used together with timing belt, very convenient to use. 20 Teeth contact with the belt, that minimizes the chance of the belt slipping.
- Locking Spring: With the springs, you can add the right tension you need and make your prints much more precise.
KeeYees Pro Micro ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino IDE Leonardo Bootloader
- ATMega32U4 running at 5V/16MHz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V.
- Supported by Arduino IDE V1.0.1; 4 x 10-bit ADC pins, 12 x Digital I/Os; Rx and Tx Hardware Serial Connections.
- Just connect to the On-Board micro-USB connector for programming. (If this module cannot be recognized by your computer, please refer to this link to install the driver https://www.arduino.cc/en/Guide/DriverInstallation)
KeeYees 5M GT2 Timing Belt 6mm Width + 4pcs 20 Teeth 5mm Bore Belt Pulley Wheel + 4pcs Idler + 4pcs Tensioner Spring Torsion + 2pcs Gear Clamp Mount Block with Allen Wrench for 3D Printer RepRap
- Timing belt: The timing belt is made of premium rubber, durable and flexible. It’s designed specifically for linear motion, high positioning accuracy. Round tooth profile guarantees that the belt tooth fits smoothly.
- Pulley: It’s used together with timing belt, very convenient to use. 20 Teeth contact with the belt, that minimizes the chance of the belt slipping.
- Locking Spring: With the springs, you can add the right tension you need and make your prints much more precise.
KeeYees Pro Micro ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino IDE Leonardo Bootloader
- ATMega32U4 running at 5V/16MHz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V.
- Supported by Arduino IDE V1.0.1; 4 x 10-bit ADC pins, 12 x Digital I/Os; Rx and Tx Hardware Serial Connections.
- Just connect to the On-Board micro-USB connector for programming. (If this module cannot be recognized by your computer, please refer to this link to install the driver https://www.arduino.cc/en/Guide/DriverInstallation)
KeeYees 5M GT2 Timing Belt 6mm Width + 4pcs 20 Teeth 5mm Bore Belt Pulley Wheel + 4pcs Idler + 4pcs Tensioner Spring Torsion + 2pcs Gear Clamp Mount Block with Allen Wrench for 3D Printer RepRap
- Timing belt: The timing belt is made of premium rubber, durable and flexible. It’s designed specifically for linear motion, high positioning accuracy. Round tooth profile guarantees that the belt tooth fits smoothly.
- Pulley: It’s used together with timing belt, very convenient to use. 20 Teeth contact with the belt, that minimizes the chance of the belt slipping.
- Locking Spring: With the springs, you can add the right tension you need and make your prints much more precise.
$33.59
Add to cart
KeeYees Pro Micro ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino IDE Leonardo Bootloader
- ATMega32U4 running at 5V/16MHz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V.
- Supported by Arduino IDE V1.0.1; 4 x 10-bit ADC pins, 12 x Digital I/Os; Rx and Tx Hardware Serial Connections.
- Just connect to the On-Board micro-USB connector for programming. (If this module cannot be recognized by your computer, please refer to this link to install the driver https://www.arduino.cc/en/Guide/DriverInstallation)
$22.09
Add to cart